Ortur YRR Rotary Roller Set Up

Ortur YRR Rotary Device

Picked up one of these Ortur YRR Rotary Rollers  to supplement my Ortur Laser Master 2.  There are a lot of videos online showing you how to assemble it as it comes in a kit form but not much information on how to make it work in software.

That’s why you have me.

I spent a couple days researching how to set it up and never really found an “AHA” video or webpage but after viewing a dozen or more items I had a good idea of what to do.

I’m going to set mine up in Lightburn which is a pay program ($40). If you have a GRBL laser cutter, Lightburn is worth every penny.

Connect your Ortur Rotary Roller to the Y axis with the supplied extension cable.

Now lets turn on the rotary support in the program.  Go to “Lightburn > Preferences” and enable rotary support.

Rotary Enable

You will then find the toggle on main window.  Turn it on.

Enable Rotary

Not done yet.  If you have your Ortur Rotary Roller connected and Rotary enabled and you start pushing buttons your machine will home to the left and the roller will spin, and spin, and spin.  It won’t hit the mechanical switch that the Y axis is used to hitting so it will run for a bit and then you’ll get an error that things are out of limits.

Now you want to go to “EDIT > MACHINE SETTINGS”.

IMPORTANT:  SAVE YOUR SETTINGS and call it “Default Machine Settings” or something like that.   Whatever you do to make the rotary work you’re going to have to un-do to make the Laser Master 2 work again. 

Now set “Soft Limits” and “Homing cycle” to false.

IMPORTANT:  Save these settings to a file called “Rotary Machine Settings” or something like that.

Rotary Setup

Now go to “TOOLS > ROTARY SETUP”.  Select the Roller Button.  Also make sure the “Enable Rotary” slider is turned on and green.

Rotary Settings

At this point you need dial calipers and need to measure the Ortur rollers and the diameter of the thing you want to etch or burn on.   Fill in those values and you will get the circumference.  Mine equals 2.755″

Go to the Lightburn working area and simply draw a box that is 2.755 inches tall.  Doesn’t matter how wide it is (but not wider than your part) but the height of the box needs to equal the circumference of your item.   NOTE THAT MY HEIGHT EQUALS 2.755 INCHES.

Draw a much thinner box inside that box and also make sure that the height is 2.755″.  Put it on its own layer and turn off output for the outer bigger box.  You will cut this small box on a scrap part.  If you don’t have a scrap part put a bunch of tape around the part you have and use low power on the laser enough to cut the tape but not cut through it.

2D Representation of your part

Now you simply frame up the part to make sure you aren’t shooting laser beams everywhere and then hit START and etch.  I used a piece of scrap dowel rod to set mine up.

The goal is to have the etched box ends touch as depicted in my picture below.

Good result

If the box doesn’t quite reach then go back to “TOOLS > ROTARY SETUP” and increase the number in the “mm per rotation” block.  If the etch went too far, then reduce the number in the “mm per rotation” block.  Do this until you get the perfect etch as I did above.

mm per rotation

Be sure that every time you put a new item on the Rotary Roller that you change the diameter and circumference in TOOLS > ROTARY SETUP.  I ultimately tweaked mine down to 63.5 mm which seemed to be spot on.  Video of the process here:

Hope I captured enough information here to help you if you bought one of these things and are scratching your head wondering how to set it up.

 

 

 

3 thoughts on “Ortur YRR Rotary Roller Set Up

  1. Scott

    Great explanation! My laser and YRR Rotary Device arrive in the next couple of days. Meanwhile I plan on binge watching everything I can.

    Reply
  2. Joshua Dodd

    Any idea what the minimum/maximum diameter is for this? How thin a cylinder (and how wide a cylinder as well) can it etch?

    Reply
  3. Tim Theisen

    I’m having an issue with my rotary not starting up when laser fires. After about 10 seconds it does and then it does fine from that point. Any ideas what I am doing wrong?

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *